Skip to main content

Make a Windows 10 bootable USB using Command prompt

Are you a person recently purchased a netbook which is not having a DVD ROM, No problem, you can install any OS using a pendrive or USB’s.
Here is the steps.

Requirements
1. A 8GB pen drive (since the size of Windows 10 is 3.2GB)
2. Windows 10 installation files or a iso image of Windows 10 OS
3. Administrative privileges in the OS
Step 1 : Take the backup of all the data in your usb drive plug into the Machine.
Step 2: Go to device manager (Control panel –> device manager –> select disk –> select your usb drive ) and then right click –> properties –> go to policies –> Select Better performance). This step is needed for faster installation of windows 10 (You can wonder, windows 10 installed within 15 minutes with just 1GB RAM) See the following video


Step 3:   open the command prompt with administrative rights (Accessories –> right click Command prompt – and select run as administrator)
Step 4: type DISKPART  (you will get a prompt as DISKPART)
Step 5: type LIST DISK (it will list all the disks), please remember the disk number of your pen drive (see the following picture)
So, mine is disk 1
Step 6: Execute the following commands one by one,

SELECT DISK 1
CLEAN
CREATE PARTITION PRIMARY
SELECT PARTITION 1
ACTIVE
FORMAT FS=NTFS   (since windows 7 permits only NTFS, the USBs also to be formatted as NTFS, and this process will take some time)
ASSIGN
EXIT

Step 7: Now insert the windows 10 DVD drive or if you have iso image, using winrar extract it to a folder
Step 8:  go to the concerned folder in the command prompt (assume installation files of windows 10 as E:/win10)
execute the command in command prompt
E:
CD win/BOOT
BOOTSECT.EXE /NT60 G: (assigning the bootmanager to the USB. G is the drive letter for my USB)
Step 9: After getting the successful message, copy the contents of your Windows 10 installation files to your USB Drive. Thats it.
Enable Booting from  USB option in your BIOS and lets see the installation will complete within 15 minutes.!!!!
































Comments

Popular posts from this blog

Electrical Machine Design (equations)

FactorsDC Machine Transformers Induction Machines Synchronous MachinesOutput EquationPa=CoD2Ln, where Pa=P/h for generators, Pa=P for motorsFor Single Phase
Q=2.22 f Bm Ai Kw Aw d10-3
For Three Phase
Q=3.33 f Bm Ai Kw Aw d 10-3Q=CoD2 L ns
KVA Input Q=
HP * 0.746 / Cos f * hQ=CoD2 L ns
KVA Input Q=
HP * 0.746 / Cos f * h
For Turbo alternators
Q=1.11Bavac KwsVa2 L 10-3/nsOutput CoefficientCo=Bav ac* 10-3where Bav-magnetic loading and ac - electric loadingDNACo=11 Kws Bav ac 10-3Co=11 Kws Bav ac 10-3 Choice of Magnetic LoadingFlux Density in Teeth Frequency of Flux Reversals Size of machineDNAMagnetizing current, Flux Density, Iron lossIron loss, Stability, Voltage Rating, Parallel Operation, Transient ShortCircuit current Choice of Electric LoadingTemperature rise,
speed of machine, Voltage, Armature reaction, CommutationDNAOverload Capacity, Copper losses, Temperature rise, Leakage ReactanceCopper loss, Synchronous reactance, Temperature rise, Stray Load losses,
Voltage rating Flux …

How to Access MOODLE in Intranet and Internet

When Moodle is accessed either in Intranet or internet, there will not be any issue. But occasions when the MOODLE Site has to be accessed both in the intranet and in the Internet, here is a simple trick
Server Used: IBM Blade Servers
Operating system: Windows Server 2008
Moodle Version: 2.4
WAMP Server is used.
Number of Users: 3000 (Students) + 200 (Faculty)
Open the config.php from ~/moodle/config.php
include these lines
$CFG->wwwroot = 'http://'.$server_id.'/vitcc';
$CFG->dataroot  = 'C:\\wamp\\moodledata';
before the following line
$CFG->directorypermissions = 07xx;
Restart the WAMP Server and you can Check MOODLE Site both in Internet and Intranet.

The above Image tells the intranet Link and the internet link can be opened outside the campus network

Mannasim Installation in NS2 - NS2 Tutorial # 18